Advertisements
[AdSlot: TOP-1 • Reserved Container • CLS-Safe]

Igniter on Furnace Not Working? Signs, Tests and Safe Fixes

Direct Answer: A furnace that is not working usually stems from five common issues: a tripped circuit breaker, an emergency shutoff switch flipped off, a clogged furnace filter triggering high-limit switches, incorrect thermostat settings, or an electronic igniter failure. Check external switches, mode settings, and filter airflow before scheduling an emergency service call.

Advertisements
[AdSlot: ART-1 • Reserved Container • CLS-Safe]
Table of Contents

When the igniter on furnace not working, your furnace typically starts its draft inducer fan, clicks several times, and locks out completely without producing warmth.

According to 2026 national project data from Angi, replacing a failed hot surface igniter costs between $150 and $250, increasing to $350 to $500 for emergency after-hours service calls.

Complementary national data from Angi notes that flame sensor replacements cost $150 to $250, while professional diagnostic service calls average $100 to $250 per Angi.

Understanding how the electronic ignition sequence works helps homeowners identify failed igniters safely.

How Does a Furnace Igniter Work?

Modern residential gas furnaces use electronic hot surface igniters (HSI) made of silicon carbide or silicon nitride instead of wasteful standing pilot lights.

When your wall thermostat calls for heat, the furnace integrated control board executes a strict automated safety sequence before releasing natural gas:

  1. Draft Inducer Pre-Purge: The small draft inducer fan starts spinning to exhaust residual combustion gases from the heat exchanger.

  2. Pressure Switch Proving: The draft inducer draws a negative pressure vacuum, closing the safety pressure switch to confirm venting pathways are completely unobstructed.

  3. Igniter Warm-Up: The control board sends 120V line power to the hot surface igniter. Over 15 to 45 seconds, electrical resistance causes the igniter element to glow bright orange or yellow, reaching temperatures exceeding 1,800°F.

  4. Gas Valve Energization: Once the igniter reaches full ignition temperature, the control board opens the main gas valve to release fuel across the burner assembly.

  5. Flame Rectification: The burners ignite, and a dedicated flame sensor detects microamp current through the flame, signaling the control board to keep the gas valve open.

Next in this series: If your heating system experiences chronic ignition failures and is over 15 years old, evaluate replacement options in our comprehensive guide to furnace replacement cost.

What Are the Signs of a Bad Furnace Igniter?

Recognizing the symptoms of a failed hot surface igniter helps you pinpoint heating failures quickly:

  • No visible orange glow - Looking through the furnace sight glass during startup reveals complete darkness instead of a bright orange glow during the ignition phase.

  • Furnace short cycles and locks out - The draft inducer runs for 30 to 60 seconds, pauses, clicks, attempts ignition three times, and enters a 1-hour system lockout.

  • Diagnostic LED flashes ignition error - The integrated circuit board flashes a specific diagnostic LED code (typically 3 or 4 blinks depending on the manufacturer) indicating an ignition lockout.

  • Physical cracks on the ceramic element - Removing the igniter reveals a visible hairline fracture or white powdery burn mark across the dark ceramic element.

How Do You Check the Igniter Safely?

Testing a hot surface igniter with a digital multimeter provides definitive confirmation of electrical failure.

Always observe strict safety precautions: disconnect line-voltage electrical power to the furnace before servicing internal components. Potential combustion hazards and carbon monoxide risks require careful handling, as highlighted by safety guidelines from the U.S. Consumer Product Safety Commission and EPA Indoor Air Quality standards.

Follow this step-by-step resistance testing procedure:

  1. Disconnect Electrical Power: Switch off the furnace electrical service switch and trip the dedicated breaker in your main panel.

  2. Remove Burner Access Panel: Lift and remove the upper metal access panel to expose the burner compartment.

  3. Locate the Igniter Wiring Harness: Trace the two high-temperature braided wires leading from the igniter ceramic base to the plastic molex wiring harness. Unclip the plastic connector.

  4. Measure Electrical Resistance (Ohms): Set your multimeter to the lowest resistance (ohms / Ω) scale. Touch the test probes to the two terminals inside the igniter plug. According to technical specifications published by Trane Technical Support, standard silicon carbide igniters show cold resistance between 40 and 80 ohms at 75°F, while newer nitride igniters measure between 65 and 120 ohms at 75°F.

  5. Interpret the Multimeter Reading: If your multimeter displays “OL” (open loop / infinite resistance), the internal ceramic element is broken and must be replaced.

How Do You Replace a Hot Surface Igniter?

Replacing a hot surface igniter is a safe, straightforward task for handy homeowners provided basic precautions are observed:

  1. Obtain the Correct OEM Replacement: Purchase an exact OEM replacement igniter or universal silicon nitride upgrade matching your furnace brand and model number.

  2. Remove the Mounting Bracket Screw: Use a 1/4-inch or 5/16-inch nut driver to remove the single sheet-metal screw securing the igniter bracket to the burner box.

  3. Carefully Extract the Old Igniter: Slide the fragile ceramic element out of the burner compartment without banging it against adjacent metal edges.

  4. Handle the New Igniter with Extreme Care: Never touch the black ceramic element with bare fingers. Natural skin oils leave a residue that creates concentrated hot spots when heated to 1,800°F, causing premature ceramic cracking. Handle the unit exclusively by its white ceramic mounting base.

  5. Fasten Bracket and Reconnect Wiring: Align the new igniter, fasten the mounting screw firmly, reconnect the plastic molex wiring plug, and restore power.

Is It the Igniter or the Flame Sensor?

Homeowners often confuse a failed igniter with a dirty flame sensor because both components cause ignition lockouts.

The following comparison table outlines the critical differences between igniter and flame sensor faults:

Diagnostic Metric Hot Surface Igniter (HSI) Flame Sensor Rod
Primary Function Generates electrical heat to ignite natural gas Detects DC microamps to confirm flame presence
Component Appearance Flat or coiled dark ceramic element Slender bent stainless steel metal rod
Failure Symptom Element stays dark; gas burners never light Burners light for 2 to 4 seconds and shut off
Resistance / Current Reading 40 to 80 ohms cold per Trane 2µA DC to 8µA DC flame rectification signal per Trane
Typical Solution Replace broken ceramic element ($150 to $250 per Angi) Clean metal rod with fine steel wool ($150 to $250 replacement per Angi)

When Is an Ignition Problem a Job for a Pro?

While replacing an igniter is manageable, certain severe combustion issues require immediate professional attention from a licensed HVAC technician:

  • Smell of Unburned Gas: If you smell sulfur or rotten eggs near the furnace, do not touch electrical switches or light matches. Evacuate the home immediately and call your local gas utility from outside.

  • Gas Valve or Manifold Pressure Issues: Adjusting gas manifold pressures, rebuilding gas valves, or servicing burner orifices requires specialized digital manometers and licensed mechanical credentials.

  • Cracked Heat Exchanger Hazards: If burner flames flicker wildly or roll out of the burner compartment when the blower starts, the heat exchanger is cracked, posing severe carbon monoxide risks.

  • Equipment Age Considerations: According to ENERGY STAR, furnaces over 15 years old warrant full replacement consideration when experiencing frequent component failures.

To review complete troubleshooting routines across all furnace subsystems, consult our master guide for when your furnace not working. If the blower fan fails to start after ignition, read our guide to fan in furnace not working.

Frequently Asked Questions

How long does a furnace hot surface igniter last?

Silicon carbide igniters typically last 3 to 7 years depending on heating cycle frequency. Newer silicon nitride igniters feature more durable physical construction and often last 7 to 10 years or longer.

Can I light a modern furnace with a match?

No. Modern residential gas furnaces with electronic hot surface ignition systems do not feature standing pilots. The integrated control board will not open the main gas valve unless it senses a complete electrical circuit through the igniter, making manual lighting impossible and dangerous.

Why does my new igniter keep burning out?

Premature igniter failure is usually caused by touching the ceramic element with bare fingers during installation, excessive line voltage from the control board, physical contact with metal burner brackets, or moisture dripping from a leaking draft inducer drain.

How much does it cost to replace a furnace igniter yourself?

Purchasing a replacement OEM hot surface igniter from an HVAC parts retailer typically costs between $25 and $60 in materials. Replacing it yourself saves $150 to $250 in professional contractor labor fees.

Ready to Restore Safe Furnace Ignition?

Testing and replacing a failed hot surface igniter eliminates frustrating mid-winter heating lockouts and restores dependable warmth to your home.

Explore equipment options, efficiency ratings, and replacement costs in our comprehensive analysis of furnace replacement cost.

Advertisements
[AdSlot: ART-2 • Reserved Container • CLS-Safe]
Safety Warning: High voltage electrical wiring, gas lines, and pressurized refrigerant lines present severe shock, fire, explosion, or toxic gas hazards. Always shut off power at the main breaker before inspecting components. Refrigerant handling requires federal EPA certification. Gas valve and heat exchanger repairs must be performed by a licensed professional technician.
Advertisements
[AdSlot: END-1 • Reserved Container • CLS-Safe]

ComfortBench Editorial Team

HVAC Research & Editorial Staff

The ComfortBench Editorial Team researches, develops, and fact-checks practical HVAC replacement cost benchmarks and safe homeowner troubleshooting guides.

Technically reviewed by a licensed HVAC professional on 2026-11-21

Advertisements
[AdSlot: MPX-1 • Reserved Container • CLS-Safe]