When your heat pump not heating properly during cold weather, the issue usually stems from an incorrect thermostat mode setting, a severely clogged return air filter, an outdoor coil trapped in heavy ice, or a faulty reversing valve solenoid.
Professional diagnostic service calls typically range from $100 to $250 according to 2026 national pricing data from Angi, while complex HVAC repairs span $130 to $2,000 depending on the failed component.
Before calling a professional technician, methodical diagnostic checks can help you resolve simple issues or pinpoint serious mechanical faults safely.
Why Is My Heat Pump Not Heating?
An air-source heat pump does not generate heat by burning fossil fuels. Instead, it extracts latent thermal energy from outdoor air using chemical refrigerant and transfers it indoors through high-pressure vapor compression.
When this thermodynamic cycle falters, indoor living spaces stay uncomfortably chilly:
-
Thermostat configuration errors - Incorrect system mode settings or mismatched reversing valve (O/B) terminal configurations cause the heat pump to blow unconditioned or chilled air.
-
Airflow restrictions - Severely clogged air filters or blocked return grilles starve the indoor heat exchanger of airflow, tripping high-pressure safety limit switches.
-
Defrost cycle malfunctions - If the outdoor defrost control board or sensor fails, thick frost blocks the outdoor coil, preventing thermal absorption.
-
Reversing valve failure - A mechanical valve jammed in cooling mode prevents the refrigerant circuit from directing hot vapor to indoor living spaces.
Next in this series: If your outdoor heat pump unit remains offline while you await professional repairs, learn what it costs to activate your backup heat strips in our guide to emergency heat on heat pump cost.
Is the Thermostat Set Correctly for a Heat Pump?
Thermostat misconfigurations represent one of the most frequent reasons a heat pump fails to produce warmth. Unlike conventional furnace thermostats, heat pump controls must coordinate compressor operation, reversing valve energization, and auxiliary electric heat strips.
Follow these verification steps at your digital thermostat:
-
Verify System Mode and Setpoint: Confirm the thermostat system switch is set firmly to “HEAT” rather than “OFF” or “COOL”. Set the target room temperature at least 3 to 5 degrees above the current ambient room display.
-
Inspect the Reversing Valve (O/B) Setting: Heat pump thermostats feature an O/B terminal setting. Most manufacturers (including Carrier, Trane, and Lennox) energize the reversing valve in cooling mode (the “O” setting), while Rheem and Ruud units energize the valve in heating mode (the “B” setting). If this parameter was inadvertently changed during battery replacement or setup, your system will cool when calling for heat.
-
Check Thermostat Batteries: Weak alkaline batteries in wall thermostats can prevent internal low-voltage relays from closing the 24-volt circuit to your heating contactor.
If your thermostat displays blank screens or strange error codes, explore our troubleshooting walkthrough for thermostat repair.
Why Is the Fan Running but the Air Is Cold?
Homeowners switching from a traditional gas furnace to a heat pump often believe their system is blowing cold air when it is operating normally.
Gas furnaces discharge air at 120°F to 140°F, feeling intensely warm to the touch. In contrast, air-source heat pumps typically deliver supply air between 90°F and 100°F. Because human skin temperature averages approximately 98.6°F, air moving at 92°F feels slightly cool or lukewarm due to evaporative wind-chill effects.
To test whether your system is genuinely failing to heat:
-
Measure Supply vs Return Temperature: Insert a probe thermometer into your return grille and a supply register nearest the air handler. A properly functioning heat pump should generate a temperature rise of 15°F to 20°F across the coil under moderate outdoor conditions.
-
Check Outdoor Compressor Operation: Step outside and check whether the outdoor compressor and condenser fan are running. If only the indoor blower is moving air while the outdoor unit remains silent, your system is merely circulating room-temperature air.
-
Inspect Air Filters: A choked air filter restricts airflow across the evaporator coil, prompting thermal limit switches to shut off the compressor.
Could It Be Stuck in Defrost or Cooling Mode?
During freezing winter weather, moisture in the outdoor air condenses and freezes onto the outdoor heat exchanger coil. To clear this frost, heat pumps automatically enter an intermittent defrost cycle.
During normal defrost:
-
The reversing valve temporarily shifts the system into cooling mode to direct hot refrigerant into the outdoor coil.
-
The outdoor fan motor shuts off to allow heat to concentrate within the outdoor cabinet.
-
The indoor auxiliary electric heat strips turn on simultaneously to temper the indoor supply air and prevent room chilling.
-
White steam rises from the outdoor unit for 5 to 10 minutes as ice melts away.
However, if the defrost timer board or temperature sensor fails, or if auxiliary heat strips fail to energize, your heat pump will blast frigid unconditioned air into your living rooms throughout the cycle.
The following diagnostic table details normal defrost characteristics versus mechanical failure symptoms:
| Observed Symptom | Operating Condition | Underlying Cause | Corrective Action |
|---|---|---|---|
| Light white frost on coil | Normal Winter Operation | Atmospheric humidity freezing on sub-32°F metal fins | Normal; system will initiate periodic automatic defrost |
| Steam rising with outdoor fan off | Normal Defrost Cycle | Outdoor coil heating rapidly to melt ice accumulation | Allow 10 minutes for cycle completion |
| Thick ice encasing entire cabinet | Mechanical Defrost Fault | Failed defrost control board, bad sensor, or low refrigerant | Turn system to emergency heat; call licensed technician |
| Air feels like air conditioning | Valve StucK / Aux Heat Out | Reversing valve jammed in cooling or burned-out heat strips | Professional diagnostic service required |
Is It the Reversing Valve, Fan or Refrigerant?
If simple homeowner checks fail to restore heating, internal mechanical or electrical faults are likely:
-
Reversing Valve Mechanical Failure - The reversing valve uses a sliding spool actuated by a low-voltage solenoid to switch refrigerant flow directions. If the internal slide sticks mechanically or the solenoid coil burns out, the heat pump remains locked in cooling mode.
-
Outdoor Fan Motor Failure - A seized outdoor motor or bad start/run capacitor stops the outdoor fan, preventing thermal exchange with ambient air.
-
Refrigerant Leaks - Under EPA Clean Air Act Section 608, handling, recovering, and charging fluorinated refrigerants legally requires certified technicians. Leaking refrigerant starves the heat pump of thermal capacity, causing the outdoor coil to ice up heavily and tripping low-pressure safety cutouts.
If your heat pump exhibits multiple recurring faults, consult our comprehensive guide on how to fix heat pump systems.
When Should You Switch to Emergency Heat?
Emergency heat (“EM HEAT”) bypasses the outdoor heat pump compressor completely, relying solely on indoor electric resistance heating coils or a backup fossil-fuel furnace.
Switch your digital thermostat to emergency heat under these specific conditions:
-
Outdoor Unit Is Locked in Ice: If your outdoor heat pump is completely encased in thick ice, switch to emergency heat immediately to prevent compressor burnout while awaiting service.
-
Refrigerant or Compressor Failure: If the outdoor unit emits harsh screeching sounds, trips circuit breakers, or fails to start, activate emergency heat to maintain indoor warmth.
-
Pending Technician Arrival: Use emergency heat as a temporary safety measure during winter cold snaps. Avoid running emergency heat for extended periods unnecessarily, as electric resistance heating is significantly more expensive than compressor operation.
If your heat pump is more than 10 years old according to ENERGY STAR, severe compressor failure often indicates it is time to evaluate a replacement unit.
Frequently Asked Questions
Why is my heat pump blowing cold air when set to heat?
If the air feels chilly, first verify whether the indoor fan switch is set to “ON” instead of “AUTO”, which circulates unheated room air between heating cycles. Next, confirm that the reversing valve O/B setting matches your manufacturer. If the outdoor unit is not running, low refrigerant or tripped breakers may be the cause.
Can snow and ice around the outdoor unit stop heating?
Yes. Deep snow drifts blocking the base pan or outdoor coil choke off intake airflow, preventing the heat pump from extracting ambient warmth. Keep at least two feet of clear space around the outdoor unit and clear heavy snow away from the cabinet.
How much does it cost to fix a heat pump reversing valve?
Replacing a heat pump reversing valve typically costs between $450 and $1,200 including labor and refrigerant recovery. Because this repair requires evacuating and recharging the closed refrigerant system, it must be performed by an EPA Section 608 certified technician.
Is it normal for a heat pump to run constantly in winter?
Yes. Unlike gas furnaces that cycle on and off abruptly, heat pumps are engineered to run for long, continuous cycles at lower supply air temperatures to maintain steady, even indoor comfort during sub-freezing weather.
Ready to Restore Reliable Winter Heating?
Troubleshooting your heat pump ensures your home stays warm, protects vital compressor components from freeze damage, and prevents unnecessary utility bill spikes.
Learn how auxiliary heat strips affect your electric bills and discover operational cost benchmarks in our detailed analysis of emergency heat on heat pump cost.